A COMPLETE GUIDE TO SEPTIC TANK REPAIR
Oh, no. Your bathroom is full of the disgusting smell of waste. It might be that your septic tank may be damaged and could require repairs. Septic tanks are one of the most important parts of our home because they handle the dirty job of taking care of our waste. With that said, having your septic tank stop working is a problem that becomes worse with each passing minute.
You know you need to take care of this ASAP, but working on septic tanks isn’t the easiest thing in the world. What you need is a septic tank repair guide to help you figure out what it takes to get your tank back up and running again.
This article has the information that you need to make it happen. Read on to find out how to get your septic pumping repaired!
1. DISLODGE THE OBJECT FROM THE SYSTEM
In most cases, solving your septic tank dilemma usually only takes a few moments to dislodge an object or the waste from the plumbing. To do this, you’ll need a plumber’s snake to get the job done.
A plumber’s snake is a tool designed to reach deep into the plumbing system of a toilet or shower and dislodge the object from the system. Plumber’s snakes are very affordable and can be purchased from just able any tool shop. Make sure to give this option a try before you consider doing anything else.
2. CHECK THE DRAIN PIPE
If the plumber’s snake doesn’t work, the next thing you’ll want to do is check out the drain pipe. Sometimes, large debris flowing out of the tank can end up blocking the drain. In other instances, there may be plants growing down in the drainage area and disrupting the flow of the drainage.
If this is the problem, you’ll need to use a special tool to cut up the blockage into smaller parts. The parts will flow down with the rest of the water and clear the path of your drainage.
3. TAKE A LOOK AT THE SEPTIC PIPE
Before you jump to the conclusion that the septic pump itself is to blame, you may want to have a look at your septic pipe. To reach the piping, you’ll have to do some digging to remove the dirt from the top to access it.
Once you reach the septic line, open the lid to check the level of liquid built up underneath. If the liquid is below the inlet of the house, then you have a blockage at the end of the inlet. This can be removed by using some pressure from your trusty garden hose to remove the stubborn object.
4. CHECK THE SEPTIC TANK LID FOR CRACKS
Septic tank lids are an important part of the septic system, and without them, the smell of the waste will escape and further damage could potentially occur. This is why the tank lids are created using a thick concrete slab that’s designed to last for many years and keep the smell of waste away from the home.
However, everything eventually falters, and the septic tank lid is no exception. If you suspect that your septic tank pumping may be the root of your problems, check out the tank lid to see if you can spot any cracks or other deformations.
To make sure you spot all of the possible damage to the lid, you’ll need to clean it off first. Do this by scraping the lid with a flat screwdriver or a putty knife to remove the majority of the gunk on the lid, and follow up with a wire brush to brush off the remaining grime. Make sure to spray down the lid with your hose to make it easier to spot any cracks on the surface.
Keep in mind that septic tank lids can be very expensive to replace; however, doing a DIY job may not always be the best option for something this crucial to your home. If you still want to try it out, you’ll need to use a concrete epoxy crack filler kit to fill in the cracks. Add pressure when using this filler to help it penetrate deep into the cracks so the formula can maximize the lid’s lifespan.
5. PUMP YOUR SEPTIC TANK
Finally, if all else fails (or if the previous steps aren’t the problem) then the last thing you’ll need to look into is pumping out your septic tank. If your tank is full of waste, your pipes are going to back up and the toxic smell of waste is going to fill up your home. A simple septic pumping will do the trick.
Septic tank pumping is very inexpensive – around $200 to $400 or average – and once the tank is pumped, you won’t have to worry about another pump job for years to come. Give your tank a septic cleaning to get it back to working at its best!
FOR THE BEST SEPTIC TANK REPAIR SERVICES
Now that you know all about properly handling a septic tank repair, you’ll be able to fix up your tank and get it working again in no time. That said, some septic tank problems may be too big for you to handle on your own. If that’s the case, you’re going to need a professional to help you handle the job. We’re the right team to help you succeed.
ACME Plumbing Service consists of experts who are dedicated to making sure their customers are satisfied with every job. We cover all things plumbing, including septic repairs, drain cleaning, well pump repairs, sump pump and sewage pump repairs, and much more. We also offer plenty of plumbing tips to help you recognize a problem in your system so we can work together to fix it in a flash.
Check out our site to see everything we have to offer, and make sure to reach out to us whenever you’re ready to schedule a service. Let’s get your plumbing back in condition!